DAQ VXI-SC-1102 Manual de Instruções Página 94
- Página / 151
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 14 SCXI Hardware
DAQ Hardware Overview Guide 14-20 www.ni.com
The following MIO and AI device resources are reserved by SCXI:
• The E Series devices use digital I/O lines 0, 1, 2, and 4 for
communication with SCXI. Other digital I/O lines are available for
Digital I/O functions and you can configure them for either input or
output on an individual basis.
• When you use an SCXI-1140 module, the scan interval counter on the
MIO or AI device controls the track/hold state of the module. When
you set up the module for a single-channel operation, NI-DAQ reserves
the scan interval counter. Refer to the
SCXI_Track_Hold_Setup
function for more information.
• The SCXI-1100 module drives the MIO or AI device analog input
channel 0; if you use the SCXI terminal block with the temperature
sensor in the DTEMP configuration, the SCXI-1100 also drives analog
input channel 1 of the MIO or AI device (except parallel ports).
• The SCXI-1120, SCXI-1120D, and SCXI-1125 modules drive analog
input channels 0 through 7 on the MIO or AI device, even if you are
operating the module in multiplexed mode. In addition, if the
temperature sensor on the terminal block is in the DTEMP
configuration, the SCXI-1120 and SCXI-1120D also drive analog
input channel 15. Notice that you must operate the MIO or AI device
in or NRSE mode to read the temperature sensor in the DTEMP
configuration.
• The SCXI-1121 module drives analog input channels 0 through 3 on
the MIO or AI device, even if you are operating the module in
multiplexed mode. In addition, if the temperature sensor on the
terminal block is in the DTEMP configuration, the SCXI-1121 also
drives analog input channel 4.
• The SCXI-1122 module drives analog input 0; if you use the SCXI
terminal block with the temperature sensor in the DTEMP
configuration, the SCXI-1122 also drives analog input channel 1 of the
MIO or AI device.
• The SCXI-1140 module drives analog input channels 0 through 7 on
the MIO or AI device, even if you are operating the module in
multiplexed mode.
• The SCXI-1141, SCXI-1142, and SCXI-1143 modules drive analog
input channels 0 through 7 on the MIO or AI device, even if you are
operating the module in multiplexed mode.
- DAQ Hardware Overview 1
- Important Information 3
- Chapter 14 7
- SCXI Hardware 7
- Glossary 10
- Contents 11
- About This Guide 12
- MIO and AI Device Terminology 15
- Table 1 16
- Related Documentation 17
- MIO and AI Devices 18
- Chapter 1 MIO and AI Devices 19
- E Series Data Acquisition 20
- Set_DAQ_Device_Info 22
- MIO Device Analog Output 24
- E Series Digital I/O 26
- E Series PFI Pins 27
- Lab and 1200 Devices 28
- AI_Trigger_Config.vi 31
- DAQ_StopTrigger_Config 31
- Table 2-2 32
- Lab and 1200 Devices Groups 33
- Figure 2-1 34
- 1200 Device Acquisition Rate 35
- 1200 Device Calibration 36
- LPM Devices 37
- DAQ_Config 38
- LPM Device Digital I/O 39
- LPM Device Counter/Timers 40
- 516 Devices and 41
- DAQCard-500/700 Devices 41
- DAQ_Config. If you do 43
- Counter/Timer Operation 44
- Figure 4-2 45
- AT-AO-6/10 Analog 46
- Output Devices 46
- AT-AO-6/10 Digital I/O 48
- 6703/6704 Devices 49
- PC-TIO-10 Timing I/O Device 50
- PC-TIO-10 Counter/Timers 54
- PC-TIO-10 Digital I/O 55
- DIO-96 Digital I/O Devices 56
- DIO-96 Groups 57
- DIO-24 (6503) 58
- AT-MIO-16DE-10, and 6025E 58
- DIO-32F and 6533 60
- Digital I/O Devices 60
- Digital_Buffer_Write.vi) 62
- AMUX-64T External 63
- Multiplexer Accessory 63
- Table 11-2 64
- AMUX-64T Channel Numbers 64
- SCAN_Setup or 65
- MIO_Config 67
- Accessories 68
- SC-2042-RTD Accessory 69
- SC-2043-SG Accessory 69
- SCC Series Modules 70
- SCC-CI20 Current Input Module 72
- SCC-LP Lowpass Filter Modules 73
- SCC Configuration 74
- SCXI Operating Modes 76
- Chapter 14 SCXI Hardware 77
- SCXI Data Acquisition Device 80
- SCXI-1200 80
- SCXI Analog Input Modules 81
- SCXI-1100 81
- SCXI-1101 82
- SCXI-1104/C 83
- SCXI-1112 83
- SCXI_Scale function to 84
- SCXI_Single_Chan_Setup 84
- SCXI-1125 85
- SCXI-1122 85
- SCXI-1126 86
- SCXI-1127 87
- SCXI-1140 87
- SCXI Analog Output Module 89
- SCXI-1124 89
- SCXI Digital Modules 90
- SCXI-1160 and SCXI-1161 90
- SCXI-1162 and SCXI-1162HV 91
- SCXI-1163 and SCXI-1163R 91
- SCXI-1530, SCXI-1531 92
- SCXI-1540 92
- SCXI_Track_Hold_Setup 94
- DIO-24 and the DIO-96 96
- DIO-32F and 6533 Device 97
- VXI-DAQ Devices 99
- AO_Change_Parameter or the 100
- Multifunction VXIbus Devices 101
- VXI-DAQ Signal Conditioning 102
- VXI-SC-1102 Submodule 103
- VXI-SC-1150 Submodule 103
- PXI DAQ Devices 104
- PXI DAQ Signal Conditioning 105
- NI 5411 Devices 106
- Chapter 17 NI 5411 Devices 107
- DDS Mode 108
- Table 17-2 110
- NI 5411 Operational Modes 110
- Device Analog Input 112
- Data Acquisition 113
- Acquisition Timing 114
- Current Source 115
- Digital I/O 115
- Device Input 116
- Chapter 19 NI 40XX Devices 118
- DSA Devices 119
- and NI 455 120
- Analog Input Channels 120
- Data Acquisition Timing 121
- Channels 122
- Digital I/O 123
- Counter/Timer Operation 124
- Devices 125
- Chapter 21 671X Devices 126
- Technical Support Resources 129
- Worldwide Support 130
- Numbers/Symbols 131
Manuais e produtos relacionados com Amplificadores áudio DAQ VXI-SC-1102
(57 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais