DAQ VXI-SC-1102 Manual de Instruções Página 90
- Página / 151
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 14 SCXI Hardware
DAQ Hardware Overview Guide 14-16 www.ni.com
chassis, you do not need to cable the SCXI-1124 to anything; NI-DAQ will
communicate with the module using the SCXIbus backplane. In this case,
the MIO/DIO jumpers on the module are irrelevant. If you plan to use
analog input SCXI modules in addition to the SCXI-1124, and you are not
using an SCXI-1200 DAQ module, you should cable one of the analog
input modules to the DAQ device.
If you are using remote SCXI, you can use the SCXI-1124 with or without
the SCXI-1200 DAQ module, because NI-DAQ will communicate with the
SCXI-1124 via the backplane and through the serial port cable.
SCXI Digital Modules
The following devices are SCXI digital modules.
SCXI-1160 and SCXI-1161
The SCXI-1160 is a 16-channel power relay module with 16 independent
one-form C relays. The relays are latched—the module powers up with its
relays in the position in which they were left at power down. You can set
or reset each relay without affecting the other relays, or all relays can
change state at the same time.
The SCXI-1161 is an 8-channel power relay module with eight
independent one-form C relays. The relays are nonlatched, and the module
powers up with its relays in the Normally Closed (NC) position or when the
hardware reset is set on the module. You can set or reset each relay without
affecting the other relays, or all the relays can change state at the same time.
The SCXI-1160 and SCXI-1161 modules only support multiplexed (also
known as serial) mode. If you cable an MIO or AI device, or Lab or
1200 device, to one of these modules, you must set jumpers on the module
to the MIO position. If you cable a DIO device to one of these modules, you
must set jumpers on the module to the DIO position. If you have not cabled
any device to the module, NI-DAQ will be using the SCXIbus backplane to
communicate with the module, therefore the MIO/DIO jumpers are
irrelevant.
If you are using remote SCXI, you can use the SCXI-1160 or SCXI-1161
with or without the SCXI-1200 DAQ module, because NI-DAQ will
communicate with the SCXI-1160 or SCXI-1161 via the backplane and
through the serial port cable.
- DAQ Hardware Overview 1
- Important Information 3
- Chapter 14 7
- SCXI Hardware 7
- Glossary 10
- Contents 11
- About This Guide 12
- MIO and AI Device Terminology 15
- Table 1 16
- Related Documentation 17
- MIO and AI Devices 18
- Chapter 1 MIO and AI Devices 19
- E Series Data Acquisition 20
- Set_DAQ_Device_Info 22
- MIO Device Analog Output 24
- E Series Digital I/O 26
- E Series PFI Pins 27
- Lab and 1200 Devices 28
- AI_Trigger_Config.vi 31
- DAQ_StopTrigger_Config 31
- Table 2-2 32
- Lab and 1200 Devices Groups 33
- Figure 2-1 34
- 1200 Device Acquisition Rate 35
- 1200 Device Calibration 36
- LPM Devices 37
- DAQ_Config 38
- LPM Device Digital I/O 39
- LPM Device Counter/Timers 40
- 516 Devices and 41
- DAQCard-500/700 Devices 41
- DAQ_Config. If you do 43
- Counter/Timer Operation 44
- Figure 4-2 45
- AT-AO-6/10 Analog 46
- Output Devices 46
- AT-AO-6/10 Digital I/O 48
- 6703/6704 Devices 49
- PC-TIO-10 Timing I/O Device 50
- PC-TIO-10 Counter/Timers 54
- PC-TIO-10 Digital I/O 55
- DIO-96 Digital I/O Devices 56
- DIO-96 Groups 57
- DIO-24 (6503) 58
- AT-MIO-16DE-10, and 6025E 58
- DIO-32F and 6533 60
- Digital I/O Devices 60
- Digital_Buffer_Write.vi) 62
- AMUX-64T External 63
- Multiplexer Accessory 63
- Table 11-2 64
- AMUX-64T Channel Numbers 64
- SCAN_Setup or 65
- MIO_Config 67
- Accessories 68
- SC-2042-RTD Accessory 69
- SC-2043-SG Accessory 69
- SCC Series Modules 70
- SCC-CI20 Current Input Module 72
- SCC-LP Lowpass Filter Modules 73
- SCC Configuration 74
- SCXI Operating Modes 76
- Chapter 14 SCXI Hardware 77
- SCXI Data Acquisition Device 80
- SCXI-1200 80
- SCXI Analog Input Modules 81
- SCXI-1100 81
- SCXI-1101 82
- SCXI-1104/C 83
- SCXI-1112 83
- SCXI_Scale function to 84
- SCXI_Single_Chan_Setup 84
- SCXI-1125 85
- SCXI-1122 85
- SCXI-1126 86
- SCXI-1127 87
- SCXI-1140 87
- SCXI Analog Output Module 89
- SCXI-1124 89
- SCXI Digital Modules 90
- SCXI-1160 and SCXI-1161 90
- SCXI-1162 and SCXI-1162HV 91
- SCXI-1163 and SCXI-1163R 91
- SCXI-1530, SCXI-1531 92
- SCXI-1540 92
- SCXI_Track_Hold_Setup 94
- DIO-24 and the DIO-96 96
- DIO-32F and 6533 Device 97
- VXI-DAQ Devices 99
- AO_Change_Parameter or the 100
- Multifunction VXIbus Devices 101
- VXI-DAQ Signal Conditioning 102
- VXI-SC-1102 Submodule 103
- VXI-SC-1150 Submodule 103
- PXI DAQ Devices 104
- PXI DAQ Signal Conditioning 105
- NI 5411 Devices 106
- Chapter 17 NI 5411 Devices 107
- DDS Mode 108
- Table 17-2 110
- NI 5411 Operational Modes 110
- Device Analog Input 112
- Data Acquisition 113
- Acquisition Timing 114
- Current Source 115
- Digital I/O 115
- Device Input 116
- Chapter 19 NI 40XX Devices 118
- DSA Devices 119
- and NI 455 120
- Analog Input Channels 120
- Data Acquisition Timing 121
- Channels 122
- Digital I/O 123
- Counter/Timer Operation 124
- Devices 125
- Chapter 21 671X Devices 126
- Technical Support Resources 129
- Worldwide Support 130
- Numbers/Symbols 131
Manuais e produtos relacionados com Amplificadores áudio DAQ VXI-SC-1102
(57 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais